Salt Spray Chamber Specification And Technical Parameters

Salt Spray Chamber Specification And Technical Parameters&#;The salt spray chamber simulates corrosion test in artificial environment. It is a simple and effective method to check whether metal materials or other test item has corrosion protection or not. It will be suitable for corrosion test of discontinuity, control and damage in organic and inorganic coatings.
Meanwhile, For a quality control purposes, Comparisons can be made between test samples coated with the same paint. Salt spray tests are particularly useful for detecting discontinuities, proportionally small holes and other defects in certain metals, organic, phase-grade oxidation and conversion coatings.
Question: When I processed a salt fog test according to ASTM B117, The water in the test room and salt water tank will choose distilled water or normal water ? Answers: Our suggestion is the filtered tap water. When you chose the tap water without filter, After a long period test, The water pipes and valves inside the salt spray chamber has some dirty oil and dust there. The pipe blockage makes the salt fog flow not smoothly. So use the tap water with filter will extend the service life of your salt spray chamber. Above picture is an example, This should be easier way to make you understand how the filtered tap water works. Question: After the first test runs and the first cleaning we found some red residues (rust?) in the test chamber and in the sewage of the waste water outlet &#; Have you ever seen this problem ? What is the root cause of this rust ? Is there any bad influence to the testing results ? Answers: This is the normal circumstances. Because the salt spray corrosion is the maximum damage when you processed an environmental test. After a fully salt and corrosion test, The surface of PVC plate may occur some rust. Question: How often should we change the water in the test room and salt water tank ? Manual water export ? Answers: The water in the salt water tank will be used up by an evaporative way within 2 days continuous test work ! The water in the bigger water tank, During your testing moment, There may have some evaporative as well. Once you have finished your testing work, Please remove the water and clean this salt spray chamber. Make it stand by there for next testing work. Question: How often and how should we clean the salt spray chamber ? When I checked the salt spray chamber specification user manual, I can not find the explanation there. Answers: Please consider this salt spray chamber is one of your household appliances. Do the clean work as you are at home for your household appliances clean work. During your clean work moment, if there any problems happen. Please taken the photos and to us, Then we will give you some suggestion once we have checked your coming photos. Question: Is it necessary that two measuring cups are closed with this white pipe plug ? If not what will be the consequence &#; higher PH-Value ? Answers: Equip the white cup on this two measuring cups are not compulsive. Make this white cup on or not on, Will no affect your testing result. The salt spray chamber specification and technical parameters user manual has some guidance to teach you how to equip the measuring cups. Meanwhile, We will make some short videos to guidance customer how to process their testing work. Question: Two Measuring Cups&#;How and how often should we check the PH-Value of this water ? Answers: In fact, The measuring cup is a measuring tool which will judge the salt spray test is valid or not. Normally, One hour the salt water come to measuring cup will be 1.5ml ~ 2ml. So if you have processed a 10 hours salt test, The measuring cup will comes to be 15ml ~ 20ml salt water. The engineer use this way to check their salt fog test successful or not. Question: Two Measuring Cups (50 ml)&#;Could we use bigger cups (up to 100 ml)? During the weekend we can&#;t pour out these cups, so they will overflow. Answers: The 50ml is the international and traditional way ! The 100ml measuring cups is ok, It will no effect your salt spray chamber during salt chamber testing moment. If you can make sure the slat fog test is working well, Then you can use a bucket to instead of the measuring cups. The main purpose for measuring cups are collecting the salt fog quantity. So make a change is not a problem when you have familiar with your salt chamber. Question: Two Measuring Cups (50 ml)&#;If there is a difference in the amount of water between the two cups &#; What can we do/ adjust that the amount will be almost equal ? Does this mentioned on your salt spray chamber specification user manual ? Answers: Please no worries about this issue. During the testing, The salt fog occur. The left side collection tube and right side collection tube may receive the salt fog has some difference. It&#;s normal circumstances.

In fact, These technical questions comes from our Austria customer. A new engineer use our salt spray chamber and it seems he has no experience to use the salt spray chamber for his test before. We have prepared some salt spray chamber specification and answer the customer questions timely when we are available.

Question: What is the salt spray chamber hsn code ? Where can I do the salt spray chamber calibration ? What is the salt spray chamber working principle ? Answers: In China, We mostly use the HS code for salt spray chamber export work. Salt spray chamber HS code what we frequently used: . Regarding the calibration, We have a supplier which is a independent third party certifier provider. We will pay the cost and request them come for a calibration work before shipment. Question: We prefer the salt spray chamber manufacturers in Delhi, in bangalore India. Can you support this ? Do you have the sales representative in Chennai India ? Answers: For this moment, We have some sales order from Delhi and bangalore India. If you need the local installation work, We prefer to find a local service engineer to support you. We will pay the service cost to the engineer who worked for us.

Please visit our website for more information on this topic.

Meanwhile, For a quality control purposes, Comparisons can be made between test samples coated with the same paint. Salt spray tests are particularly useful for detecting discontinuities, proportionally small holes and other defects in certain metals, organic, phase-grade oxidation and conversion coatings.

Salt Spray Chamber Specification And Technical Parameters&#;The salt spray chamber simulates corrosion test in artificial environment. It is a simple and effective method to check whether metal materials or other test item has corrosion protection or not. It will be suitable for corrosion test of discontinuity, control and damage in organic and inorganic coatings.

The salt spray chamber specification and technical parameters is important for a new engineer who has no experience for a salt spray chamber operation work. We have an Austria customer, He asked the salt spray chamber specification and technical parameters from our technical dept. Because he has no idea on his testing process. Below are some salt spray chamber specification according to our Austria customer mentioned. Let me do a summary here to make the new engineer easier understand the salt spray chamber specification. It should be a convenient way to improve the new engineer operation skills for the salt spray chambers.

Optional AccessoryRef.DescriptionFactory Fit Only

Salt Solution Resevoir (80 Litres)

ACC59/1

An 80 Litre (21 US gal) capacity salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 460mm/18&#; (w) x 620 mm/24&#; (d) x 675mm/26&#; (h)

Salt Solution Reservoir (115 Litres)

ACC59/5

A 115 Litre (30US gal) capacity salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 560mm (w) x 620 mm (d) x 675mm (h)

Salt Solution Resevoir (160 Litres)

ACC59/9

A 160 Litre (42.2 US Gal) capacity salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 840mm (w) x 500mm (d) x 790mm (h)

Extra Heater Mats

ACC03

Wrap around heater mats fitted to the sides of the chamber to allow the chamber to maintain temperatures of 60 Degrees Celsius during the salt spray phase,

These extra heaters can be fitted to Salt Spray 450L and above, they are not available on CCT or Atmosfär range as these chambers already have them fitted as standard.

*Exact part number dependent on chamber size.

Air Compressor (large)

ACC04/2

A large free standing compressor, to provide a continuous supply of clean, dry and oil free compressed air, to enable the chamber to function without requiring connection to a local compressed air supply.

Electrical supply: 220-240VAC single phase, 50Hz
Output : 300 l/min displaced
Free Air Delivery (FAD) @ 6 Bar : 179 l/min
Max pressure: 8 Bar
Air receiver: 59 litres
Noise output: 74dB (A) measured at a distance of 1m

Guardian Angel System - Standard LED Version

ACC05/1

Modular traffic light alarm system fitted to the top of chambers, to provide visual notification of chamber status.

Only available for Premium chambers (iP designations)

Guardian Angel System - LED Version, with USB Connectivity

ACC05/2

Modular traffic light alarm system fitted to the top of chambers, to provide visual notification of chamber status, with USB connectivity for remote monitoring.

Only available for Premium chambers (iP designations)

Guardian Angel System - LED Version, with Ethernet Connectivity

ACC05/3

Modular traffic light alarm system fitted to the top of chambers, to provide visual notification of chamber status, with Ethernet connectivity for remote monitoring.

Only available for Premium chambers (iP designations)

Guardian Angel System - USB add on only

ACC05/4

Retrofit add on for Guardian Angel, allows addition of USB connectivity for remote monitoring.

Only available for Premium chambers (iP designations)

Guardian Angel System - Ethernet add on only

ACC05/5

Retrofit add on for Guardian Angel, allows addition of Ethernet connectivity for remote monitoring.

Only available for Premium chambers (iP designations)

Water Deioniser System (Small)

ACC06/1

To provide water of suitable purity for topping up a salt spray/cyclic corrosion chamber air saturator, and for making up salt solution to be sprayed.

Requires connection to a continuous mains water supply of maximum pressure 5.0 bar.

This system comprises of a regenerable cylinder deioniser and an electronic conductivity indicator. Must be regenerated or replaced when exhausted.

Water Deioniser System (Medium)

ACC06/2

To provide water of suitable purity for topping up a salt spray/cyclic corrosion chamber air saturator, and for making up salt solution to be sprayed.

Requires connection to a continuous mains water supply of maximum pressure 5.0 bar.

This system comprises of a regenerable cylinder deioniser and an electronic conductivity indicator. Must be regenerated or replaced when exhausted.

Water Deioniser System (Large)

ACC06/3

To provide water of suitable purity for topping up a salt spray/cyclic corrosion chamber air saturator, and for making up salt solution to be sprayed.

Requires connection to a continuous mains water supply of maximum pressure 5.0 bar.

This system comprises of a regenerable cylinder deioniser and an electronic conductivity indicator. Must be regenerated or replaced when exhausted.

35mm Entry Port

ACC10/1

Sealable chamber entry port of 35mm (1.27&#;) through the chamber&#;s left hand wall to enable the connection of external monitoring/driving equipment.

Note: not suitable for use with option ACC46.

110mm Entry Port

ACC10/2

Sealable chamber entry port of 110mm (4.33&#;) through the chamber&#;s left hand wall to enable the connection of external monitoring/driving equipment.

Note: not suitable for use with option ACC46 or 120Ltr chambers

Hand-held salinity refractometer

ACC100

A salinity refractometer optimized to give a direct reading of percentage sodium chloride in the range 0 to 28%, with automatic temperature compensation.

A single drop of the salt solution to be measured is placed on the viewing window, using the pipette supplied, and its salinity read against a high contrast scale, graduated in % sodium chloride, to give an accurate reading.

Salt Solution Consumption Sensor

ACC102 

Electronic liquid flow sensor mounted inside the chamber and sensor situated in-line between the salt solution reservoir and the salt spray atomizer. The sensor measures the flow of salt solution from the reservoir to the atomizer. The output from the is displayed digitally at the chamber display as instantaneous consumption in ml per min and total consumption in ml.

Designed for use where a high salt solution flow rate is required and where that flow rate should be displayed electronically, such as Renault D17 . This has collection rates that equate to 4-6ml/80cm²/hr. This system may not work effectively at collection rates below this.

Only available for Premium chambers (iP designations).

Fallout Measuring Kit

ACC108

Comprises of 4 x 100ml measuring cylinders and 4 x 100mm funnels, for manually collecting and measuring salt spray fall-out inside a chamber, during salt spray testing.

Hand held pH meter

ACC11

Digital pH meter, for measuring the pH of salt solution fallout over range 0-14 pH with a resolution of 0.01 pH. Supplied complete with buffers for calibration.

Vertically Operating Canopy

ACC110

Special design of canopy to allow it to open to a vertical position to enable access from above (e.g. by hoist) for large and/or heavy test samples.

*Exact part number dependent on chamber size.

12 Month Consumables Kit for Cyclic Chambers

ACC57/2

A kit of consumables sufficient for operating an Ascott Atmosfär, Kesternich, Cyclic or Salt Spray Premium chamber for up to 1 year.

Includes Salt Filters for Atomiser, Silicone tubing, Humidity Prove Filter Cap with O Ring & Air Filter

Note: A consumables spares kit is supplied as standard with every new chamber.

36 Month Servive & Spares Kit

ACC12/2

An initial kit of spare parts for servicing and maintaining a chamber for up to 3 years from its first use.

72 Month Service & Spares Kit

ACC12/3

A comprehensive kit for servicing and maintaining a chamber for up to 6 years from its first use, or its last service.

Data Logging Software

ACC121

This software allows logging of chamber variables and editing of chamber programs. It is uses a graphics based display which mimics and improves on the chamber interface. It can be loaded on Workstations or Laptops with Operating systems of Windows 10, Windows 8 Professional, Windows 7 Professional, Windows (SP4+), Windows XP Professional (SP3+). It also requires the following minimum hardware requirements &#; 1 GHz Processor minimum Processor, 256 MB RAM, video x (high colour 16 bit) and it is advised 2GB Hard Disk Space for data. The software communicates via an Ethernet network adaptor from chamber to PC / Laptop. The Workstation / Laptop also require a USB port to load the software and to accommodate the Dongle that is needed to run this software. Network must also be suitable as it will only work across a network on Class C subnet masks/ IP addresses &#; please liaise with your IT departments to confirm this or contact Ascott for further information.

Only available for Premium chambers (iP designations).

Mesh Racking

ACC15

Mesh type racking with an aperture of 30mm for testing small component parts.  Locates on either the upper or lower level supports provided as standard inside the chamber, and removable if required.  This product is available in a variety of sizes to suit different capacity chambers.

Slotted Sample Racks

ACC16

Removable slotted type sample rack for testing panels/coupons. Each slot is 3mm/1/8&#; wide and angled at 15 degrees from vertical. Such racks are supplied as standard, unless otherwise specified. Wider slots and/or different angles are available on request.

*Exact part number dependent on chamber size.

General Motors Test Plate Kit

ACC16/6

A kit of 10 specially designed Polycarbonate test plate holders and nylon fixings, as pictured, for mounting General Motors test plates in accordance with the requirements of GMW &#; in an existing Ascott slotted sample rack, ref ACC16.

Variable Sample Racks

ACC14

Slotted sample racks for testing coupons on which the slot width and slot angle can be varied.

Rod Sample Racks

ACC17

Removable rod type sample rack for suspending small test samples hung beneath, or for supporting larger test samples placed on top of these racks.

*Exact part number dependent on chamber size.

Spiked Sample Racks

ACC18

Removable spiked type sample rack for suspending test samples from the 10mm/0.4&#; diameter x 55mm/2&#; long spikes, equally spaced, and protruding from opposite sides.

*Exact part number dependent on chamber size.

Reinforced False Floor

ACC19

Removable reinforced false floor, providing a horizontal platform over the chamber base for supporting large/heavy test samples.

*Exact part number dependent on chamber size.

Waste Water Trough & Pump

ACC20

Where a floor level drain connection is unavailable this option provides a holding tank into which the chamber drain outlet is terminated. When full, waste water is automatically pumped to an existing remote drain/effluent tank, up to 10m/32ft horizontally & 3m/10ft vertically from the chamber.

Note: not suitable for use with option ACC46.

Trolley

ACC24

Converts the bench standing 120 Ltr size chamber to floor standing. Mounted on lockable castors. There is space underneath for one additional reservoir (separate option ref: ACC59).

Interior Lighting

ACC26

Illuminates the chamber interior when a control panel push-button is pressed.

*Exact part number dependent on chamber size.

Hand Held Temperature & Humidity Probe

ACC28

Precision hand-held thermo-hygrometer for independently checking the chamber temperature and humidity. Includes a special salt resistant measuring probe mounted on an extension cable. Range: -40 to +85°C & 0 to 100%RH.

Requires any size entry port (see option ACC10) to access the chamber interior.

110V Transformer

ACC33

Transformer to convert chambers to 110 Volts.

*Exact part number dependent on chamber size.

Note: only needed for SiS chambers.

Re-transmission of Temperature & Humidity

ACC36

Re-transmission of chamber temp & humidity as 2 x 0-10VDC signals via externally mounted socket. For remote data logging.

Only available for Premium chambers (iP designations).

SO2 Gas Dosing

ACC46

Designed to meet the requirements of ASTM G85 annex A4, this optional accessory comprises of a chamber mounted dispersion tube, through which SO2 gas is introduced, at a user adjustable rate and for a programmable duration.

*Exact part number dependent on chamber size.

Only available for Premium chambers (iP designations).

Notes.
The provision of the SO2 gas cylinder and connector are the users responsibility and are not included as part of this option.
The ACC46 is not suitable for use with options: ACC10, ACC34/INTERFACE, ACC92.

Temperature data logger

ACC50

A battery powered, chamber mounted data logger and temperature sensor. Continuously records the chamber air temperature (°C). Logs can be downloaded to a computer running appropriate software (provided).

Chamber Raising Kit

ACC56

Set of 4 adjustable height legs that allow the chamber to be raised to operate with high level drains.

Manual filling air saturator

ACC66

Enables the air saturator to be manually filled and periodically topped up with water by hand as an alternative to the automatic fill and top up provided as standard. Adds 75mm/3&#; to external chamber width.

80L Salt solution reservoir fitted with low level alarm

ACC59/3

An 80 Litre (21 US gal) capacity salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 460mm (w) x 620 mm (d) x 675mm (h)

Fitted with Low Level Alarm that operates if the salt solution level falls below requirement for approximately 18 hours testing low level alarm at 1-2ml/hour fall-out rates. Sounds audible alarm and displays warning message. If reservoir is not refilled within 18 hours the running chamber program will automatically pause/stop.

Window insulated cover

ACC82

Comprises of an insulated cover, which is specially shaped to match the window aperture. This will reduce the amount of condensation that can form on the inside of the window during testing and will also improve thermal efficiency.

*Exact part number dependent on chamber size.

Exhaust salt scrubber (without circulation Pump)

ACC92/1

Removes highly corrosive salt fog from the chamber exhaust where it is not convenient or possible to vent to the outside of the building. Removes salt through condensation and by spraying with water.

Note: not suitable for use with option ACC46.

Exhaust salt scrubber (with circulation Pump)

ACC92/3

Removes highly corrosive salt fog from the chamber exhaust where it is not convenient or possible to vent to the outside of the building. Removes salt through condensation and by spraying with water.

Note: not suitable for use with option ACC46.

Compressed air coupling

ACC94

A control panel mounted, quick release coupling to facilitate the connection of a third-party air pressure gauge (not supplied) for checking/calibrating the chamber&#;s own air pressure gauge.

80 Litre (21 US gal) capacity salt solution reservoir fitted with Air agitation

ACC59/2

Additional reading:
System-on-Module (SOM) Solutions - Embedded IoT
What is the Advantage and Disadvantage of difference between soc and sbc

Suntex Electronics supply professional and honest service.

An 80 Litre (21 US gal) capacity salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 460mm (w) x 620 mm (d) x 675mm (h)

Fitted with Air Agitation to assist dissolving salt within a salt solution reservoir to create a thoroughly mixed salt solution. Regulated compressed air supplies a bubbling device that rests in the bottom of the reservoir.

Note: requires connection to a compressed air supply.

Atomiser Airflow Optimiser

ACC106

An anemometer for measuring airflow and a mounting for this which positions it at a fixed distance from the end of the salt spray atomiser. This allows the airflow to be measured and if necessary adjusted. Consistent airflow at the atomiser can be a significant factor in obtaining good salt spray fall-out homogeneity, which is particularly important for some salt spray tests such as Renault ECC-1.

Increased Load Capacity Kit

ACC119

Mesh racking kit combined with strengthened fibreglass chamber interior to allow greater loads to be tested in the chamber.

*Exact part number dependent on chamber size and whether upper or lower racking is required.

80L Salt solution reservoir fitted with Air Agitation and low level alarm

ACC59/4

An 80 Litre (21 US gal) capacity salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 460mm (w) x 620 mm (d) x 675mm (h)

Fitted with Low Level Alarm that operates if the salt solution level falls below requirement for approximately 18 hours testing low level alarm at 1-2ml/hour fall-out rates. Sounds audible alarm and displays warning message. If reservoir is not refilled within 18 hours the running chamber program will automatically pause/stop.

Also fitted with Air Agitation to assist dissolving salt within a salt solution reservoir to create a thoroughly mixed salt solution. Regulated compressed air supplies a bubbling device that rests in the bottom of the reservoir.

Note: requires connection to a compressed air supply.

Salt Solution Reservoir (115 Litres) fitted with Air Agitation

ACC59/6

A 115 Litre (30US gal) capacity salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 560mm (w) x 620 mm (d) x 675mm (h)

Fitted with Air Agitation to assist dissolving salt within a salt solution reservoir to create a thoroughly mixed salt solution. Regulated compressed air supplies a bubbling device that rests in the bottom of the reservoir.

Note: requires connection to a compressed air supply.

Salt Solution Reservoir (115 Litres) fitted with Low Level Alarm

ACC59/7

A 115 Litre (30US gal) capacity salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 560mm (w) x 620 mm (d) x 675mm (h)

Fitted with Low Level Alarm that operates if the salt solution level falls below requirement for approximately 18 hours testing low level alarm at 1-2ml/hour fall-out rates. Sounds audible alarm and displays warning message. If reservoir is not refilled within 18 hours the running chamber program will automatically pause/stop.

Salt Solution Reservoir (115 Litres) fitted with Air Agitation & Low Level Alarm

ACC59/8

A 115 Litre (30US gal) capacity salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 560mm (w) x 620 mm (d) x 675mm (h)

Also fitted with Air Agitation to assist dissolving salt within a salt solution reservoir to create a thoroughly mixed salt solution. Regulated compressed air supplies a bubbling device that rests in the bottom of the reservoir.

Note: requires connection to a compressed air supply.

Fitted with Low Level Alarm that operates if the salt solution level falls below requirement for approximately 18 hours testing low level alarm at 1-2ml/hour fall-out rates. Sounds audible alarm and displays warning message. If reservoir is not refilled within 18 hours the running chamber program will automatically pause/stop.

Salt Solution Reservoir (160 Litres) with Air Agitation

ACC59/10

A 160 Litre (42.2 US Gal) capacity salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 840mm (w) x 500mm (d) x 790mm (h)

Also fitted with Air Agitation to assist dissolving salt within a salt solution reservoir to create a thoroughly mixed salt solution. Regulated compressed air supplies a bubbling device that rests in the bottom of the reservoir.

Note: requires connection to a compressed air supply.

Salt Solution Reservoir (160 Litres) with Low level Alarm

ACC59/11

A 160 Litre (42.2 US Gal) capacity salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 840mm (w) x 500mm (d) x 790mm (h)

Fitted with Low Level Alarm that operates if the salt solution level falls below requirement for approximately 18 hours testing low level alarm at 1-2ml/hour fall-out rates. Sounds audible alarm and displays warning message. If reservoir is not refilled within 18 hours the running chamber program will automatically pause/stop.

Salt Solution Reservoir (160 Litres) with Air Agitation and Low level Alarm

ACC59/12

A 160 Litre (42.2 US Gal) capacity salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 840mm (w) x 500mm (d) x 790mm (h)

Also fitted with Air Agitation to assist dissolving salt within a salt solution reservoir to create a thoroughly mixed salt solution. Regulated compressed air supplies a bubbling device that rests in the bottom of the reservoir.

Note: requires connection to a compressed air supply.

Fitted with Low Level Alarm that operates if the salt solution level falls below requirement for approximately 18 hours testing low level alarm at 1-2ml/hour fall-out rates. Sounds audible alarm and displays warning message. If reservoir is not refilled within 18 hours the running chamber program will automatically pause/stop.

Salt Solution Reservoir (90 Litres)

ACC59/13

A 90 Litre (23US gal) capacity external salt solution reservoir & removable lid for ease of filling and cleaning. Graduated scale in litres. Can be mobile and mounted on castors for mobility when purchased with ACC59/15 Salt Solution Reservoir Dolly.

External Dimensions: 540mm/21&#;  x 635mm /25&#; width x height

Salt Solution Reservoir (73 Litres)

ACC59/14

A 73Litre (19 US gal) capacity External salt solution reservoir & lid for ease of filling and cleaning. Graduated scale in litres. Can be mobile and mounted on castors for mobility when purchased with ACC59/15 Salt Soution Reservoir Dolly.

External Dimensions: 425mm Dia x 630mm (h)

Salt Solution Reservoir (73-90L) Dolly

ACC59/15

A Dolly for 73Litre (19 US gal) and 90L (23 US gal) External salt solution reservoir & lid for mobility.

12 Month Consumables Kit for Salt Spray Chambers

ACC57/1

ACC57/1 is a kit of consumables sufficient for operating a Salt Spray chamber for up to 1 year.

Includes Salt Filters for Atomiser, Silicone tubing, & Air Filter

Note: this consumables spares kit is supplied as standard with every new Salt Spray chamber.

This item can be purchased online here 

S120IS Installation Kit

ACC58/1

An Installation kit for S120iS Chambers to help you connect your chamber to your existing utilities.

Saves you time resourcing them locally and ensuring you get everything you will need.

Comprising of:

3m of 3/4&#; Drain Pipe inc couplers and elbows

3m of 2&#; Exhaust Pipework inc Couplers and Elbows

6m of 13mm Braided hose inc Clips for Air and Water connections

1/2&#; Hosetail

Coupler-1/4&#; Male-8mm to allow a push fitting.

S120IP Installation Kit

ACC58/2

A Handy Installation kit for S120iP Chamber to help you connect your chamber to your services and exhaust.

Saves you time resourcing them locally and ensuring you get everything you will need.

Comprising of:

3m of 3/4&#; Drain Pipe inc couplers and elbows

3m of 2&#; Exhaust Pipework inc Couplers and Elbows

6m of 13mm Braided hose inc Clips for Air and Water connections

1/2&#; Hosetail

Coupler-1/4&#; Male-8mm to allow a push fitting.

(Items can be purchased separately too upon request).

S450IS Installation Kit

ACC58/3

A Handy Installation kit for S450iS Chambers to help you connect your chamber to your services and exhaust.

Saves you time resourcing them locally and ensuring you get everything you will need.

Comprising of:

3m of 3/4&#; Drain Pipe inc couplers and elbows

3m of 2&#; Exhaust Pipework inc Couplers and Elbows

6m of 13mm Braided hose inc Clips for Air and Water connections

1/2&#; Hosetail

Coupler-1/4&#; Male-8mm to allow a push fitting.

(Items can be purchased separately too upon request).

S450IP Installation Kit

ACC58/4

A Handy Installation kit for S450iP Chambers to help you connect your chamber to your services and exhaust.

Saves you time resourcing them locally and ensuring you get everything you will need.

3m of 3/4&#; Drain Pipe inc couplers and elbows

3m of 2&#; Exhaust Pipework inc Couplers and Elbows

6m of 13mm Braided hose inc Clips for Air and Water connections

1/2&#; Hosetail

Coupler-1/4&#; Male-8mm to allow a push fitting.

(Items can be purchased separately too upon request).

S/IS Installation Kit

ACC58/6

A Handy Installation kit for S/iS Chambers to help you connect your chamber to your services and exhaust.

Saves you time resourcing them locally and ensuring you get everything you will need.

Comprising of:

3m of 3/4&#; Drain Pipe inc couplers and elbows

3m of 2&#; Exhaust Pipework inc Couplers and Elbows

6m of 13mm Braided hose inc Clips for Air and Water connections

1/2&#; Hosetail

Coupler-1/4&#; Male-8mm to allow a push fitting.

(Items can be purchased separately too upon request).

S/iP Installation Kit

ACC58/7

A Handy Installation kit for S/iP Chambers to help you connect your chamber to your services and exhaust.

Saves you time resourcing them locally and ensuring you get everything you will need.

3m of 3/4&#; Drain Pipe inc couplers and elbows

3m of 2&#; Exhaust Pipework inc Couplers and Elbows

6m of 13mm Braided hose inc Clips for Air and Water connections

1/2&#; Hosetail

Coupler-1/4&#; Male-8mm to allow a push fitting.

(Items can be purchased separately too upon request).

S/iS Installation Kit

ACC58/9

A Handy Installation kit for S/iS Chamber to help you connect your chamber to your services and exhaust.

Saves you time resourcing them locally and ensuring you get everything you will need.

Comprising of:

3m of 3/4&#; Drain Pipe inc couplers and elbows

3m of 2&#; Exhaust Pipework inc Couplers and Elbows

6m of 13mm Braided hose inc Clips for Air and Water connections

1/2&#; Hosetail

Coupler-1/4&#; Male-8mm to allow a push fitting

S/iP Installation Kit

ACC58/10

A Handy Installation kit for S/iP Chambers to help you connect your equipment to your services and exhaust.

Saves you time resourcing them locally and ensuring you get everything you will need.

Comprising of:

3m of 3/4&#; Drain Pipe inc couplers and elbows

3m of 2&#; Exhaust Pipework inc Couplers and Elbows

6m of 13mm Braided hose inc Clips for Air and Water connections

1/2&#; Hosetail

Coupler-1/4&#; Male-8mm to allow a push fitting.

(Items can be purchased separately too upon request).

CR4 Grade Steel Corrosion Test Panels for ISO & VDA 233-102

ACC131

Ascott CR4 Test Panels are used to check the reproducibility and repeatability of the test results for Salt Spray or Cyclic Corrosion Test Chambers being being used to run ISO or VDA 233-102

Click here to purchase CR4 Test Panels from Ascott online.

Two Button Canopy Control

ACC07

Two button canopy operation ensures that the user must stand to the side of the chamber and use both hands in order to operate the pneumatically actuated canopy

Test Plate to hold small items/fasteners

ACC43

A polycarbonate test plate holder pre-drilled with 7 holes (3 x 6mm, 2 x 5mm, 2 x 4mm) which are fitted with the nuts and bolts:

• 3 of them with fitted with an M6 x 25 nylon nut and bolt
• 2 of them with fitted with an M5 x 20 nylon nut and bolt
• 2 of them with fitted with an M4 x 25 nylon nut and bolt

When loaded with samples the plate slots into the standard slotted sample racks  (Ref ACC16)

The plate can be used in different ways, if the nuts and bolts are removed the holes can be used to suspend samples directly (as long as the samples do not fall through the hole), or small samples with a through hole (nuts, washers etc.) can be suspended on the bolts.

Sikkens® Scratch Tool

ACC49

This scratching tool is specially designed to perform scribes on coated steel panels or test substrates prior to salt spray testing for example as described in ISO & ISO -6

As standard, the scratch tool is supplied with 3 tungsten carbide cutting blades;

• 1 blade @ 0.5mm thick, the Daimler Chrysler version
• 1 blade @ 1mm thick, the original Sikkens® version
• 1 blade @ 2mm thick, requirement for update of ISO -6

The blade is positioned by an adjustable guide block to assist cutting a straight line.

The guide block can be easily adjusted using the Allen keys provided. The tool features a soft grip ergonomically designed handle for ease of use and is supplied in a carry case.

Salt Solution Reservoir (227 Litres)

ACC59/16

A 227 Litre (59.9 US Gal) salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 830mm x 640mm x 740mm

Salt Solution Reservoir (227 Litres) fitted with Air Agitation

ACC59/17

A 227 Litre (59.9 US Gal) salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 830mm x 640mm x 740mm

Also fitted with Air Agitation to assist dissolving salt within a salt solution reservoir to create a thoroughly mixed salt solution. Regulated compressed air supplies a bubbling device that rests in the bottom of the reservoir.

Note: requires connection to a compressed air supply.

Salt Solution Reservoir (227 Litres) fitted with Low Level Alarm

ACC59/18

A 227 Litre (59.9 US Gal) salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 830mm x 640mm x 740mm

Fitted with Low Level Alarm that operates if the salt solution level falls below requirement for approximately 18 hours testing low level alarm at 1-2ml/hour fall-out rates. Sounds audible alarm and displays warning message. If reservoir is not refilled within 18 hours the running chamber program will automatically pause/stop.

Salt Solution Reservoir (227 Litres) fitted with Air Agitation & Low Level Alarm

ACC59/19

A 227 Litre (59.9 US Gal) salt solution reservoir, with a graduated scale in litres, a hinging lid for ease of filling and cleaning and mounted on castors for mobility.

External Dimensions: 830mm x 640mm x 740mm

Also fitted with Air Agitation to assist dissolving salt within a salt solution reservoir to create a thoroughly mixed salt solution. Regulated compressed air supplies a bubbling device that rests in the bottom of the reservoir.

Note: requires connection to a compressed air supply.

Fitted with Low Level Alarm that operates if the salt solution level falls below requirement for approximately 18 hours testing low level alarm at 1-2ml/hour fall-out rates. Sounds audible alarm and displays warning message. If reservoir is not refilled within 18 hours the running chamber program will automatically pause/stop.

Want more information on Salt Spray Test Machine Price? Feel free to contact us.